gorski
20-01-10, 23:57
M8s, translate this into other languages, please...
Card Sharing is:
connecting your receiver [in this case Samsung DSR 9500 VIACI] with a specific SW in your receiver [in this case Gold Emu 4.x by Maestro MAHDI, plus GBox (installed on your PC!) by Maestro TaGana and the possy]
with your friends' receivers or PCs.
They will have Original Smart Cards [OSCs] you do NOT have, in order to watch the programs those OSCs open.
You connect with them via the internet.
With CS you have those cards virtually. But you can still watch the programs those OSCs can open, provided your friends are constantly "online" and you can connect to their receiver or PC.
Your Sammy, btw, is connected to the net via your PC. It is done via a Serial port at the back of your Sammy to the Serial Port on your PC. A "straight" 9 pin Serial Cable is used. Meaning: the wires are connected 2->2, 3->3, 9->9 etc. I am not sure if ALL the 9 pins are connected. Check it out on the net.
And now the "How to" in small steps:
First, How to make and use a dyndns free service/account...
It's a simple but more detailed guide than the one already provided here:
go to _[Only Registered Users Can See Links] and then...
choose a username
then a password
confirm it
provide them with a valid email [you must!]
confirm it
security image - carefully put it in the box provided
click on "I agree with Terms & conditions"
click on "Create account".
You get an email.
Click on the link provided to activate the account.
Login at the dyndns.org website.
Go to: My Service -> Add hostaname -> create it: xyz.dyndns.org or something else you choose there [they have a few].
Click on “Use auto detected IP address xx.xxx.xxx.xx”.
"Add To Cart" -> it will say something like “You must checkout to activate”.
Click on "Next" and then on
"Activate Service".
You should see: “Host Services successfully activated”.
Go and CS... :wink:
Login regularly [weekly] so they don’t delete your account! They do it without any warning!
Btw, GBox, [and the SSSP derivatives, like MGcamd and Mbox, for instance], needs this to function, for both Client and Server services. If you only use CCcam client service, it is not needed. The following will be in relation to GBox...:wink:
After that put the DynDNS details into your Router to enable your DynDNS Service updater in it, so DynDNS Service is updated every time you change your IP address and your friends can find you through the DynDNS address. Namely, in your router's DDNS options [if you have more than one]:
choose DynDNS, then ->
put your newly created DynDNS username, then
password, then
Hostname [like myname.dyndns.org - this is just an example, create your own name!!].
That address you just created is always going to be the same, even though your IP address might change every time you logon/get online/boot your PC.
Now SAVE all that or APPLY or ENABLE, whatever is in your Router's interface.
OK so far? :blush:
After that you need to forward some ports in your Router. That allows your GBox to go to the net and connect with other PCs, in this case a Server with your friends' cards, the stuff you want to watch...
Now, install UltraEdit32 on your PC. Why? Because you need to sort your cwshare.cfg yourself. Here is the template you need to Copy and Paste into UltraEdit 32, NOT Notepad, Wordpad or anything else!!!
In cwshare.cfg you will edit the yourdyndns.org and yourfriendsdyndns.whatever with the data you are given from the people you trust, like theirport but also yourport, the one you assign to your GBox, so it can go to the net. Also yourpass and hispass! JUST REPLACE THEM AS INDICATED BELLOW, IT IS EASY!!! Don't give up on me now!!! :bangin:
That's all you need to do for Sammy GBox to work your CS magic. Nothing else. No other files except cwshare.cfg!!!
===============cwshare.cfg=============
Lines with # in front are not taken into account, do not matter, these are explanations. Leave them be.
M: { your.dyndns.org { yourpass }}
# Internet Friends port range password cod
D: { yourfriendsdyndns.whatever { yourport theirport { hispass { A3 A3 }}}}
#================================================
# allow maximum 3 share level for received card data
I: { 3 }
# Send ECM's at maximum 7 cards (please use this as default)
X: { 7 }
#
# 01 repeat EMM's
# 00 consider every EMM only once
# 01 restart pid on overflow
# 1* reset ENX on every channel change
# *1 check/reset ENX freezes on FTA
# *2 check/reset ENX freezes on PayTV
# *3 check/reset ENX freezes on FTA and PayTV
# 00 write nothing in atack.txt
# 01 write into atack.txt: password is wrong
# 02 write into atack.txt: ID unknown
# 04 write into atack.txt: IP is wrong
# 08 write into atack.txt: port is wrong
# 10 write into atack.txt: share.stat
# 20 create online.log for online/offline logging
# 3F write everything. (combine bits for other combinations)
# 5000 send ecm again after 5 Seconds if no reply.
# 7000 resync decode after 7 Seconds if net decode failed
N: { 01 01 03 00 5000 7000 }Lines with # in front are not taken into account, do not matter, these are explanations. Leave them be.
Your pass will be 8 signs, letters from A - F, if memory serves, numbers from 1-9.
Just Copy and Paste this into your Ultra Edit 32 and edit CAREFULLY, preserving the empty slots [pauses/breaks], then Save.
==============To recapitulate:=================
You have created a DynDNS account and enabled it in your router.
You have installed UE32 and created a GBox folder [just unpack your GBox in that folder] on your PC.
In your cwshare.cfg file, that is a part of GBox CS SW, you have put your DynDNS details and the password for your GBox, plus the ports you have opened in your Router for it to operate freely.
You have also put your friend's details [their DynDNS address, password and port they opened for you to hook onto their GBox server] into the cwshare.cfg.
Now reboot your PC, just in case, put your Sammy on Standby, then restart it at the back with the power switch, just in case. I.e. kill the power at the back, wait for 10 seconds, turn it back on again, wait for the clock to appear on Sammy's display.
When all is ON again, as described above, start your Sammy with your Remote and put it on a scrambled channel [with just 1 system of encryption, preferably not N*D*S/Videguard, as it's difficult].
Start your GBox with the newly edited cwshare.cfg, that you put into the GBox folder.
You should see a new black window on your PC, with something like "Hello to..."
Then "Hello from..." [your friend] should appear. That is IF you are connected, if everything is properly sorted.
Change the channel to another encrypted channel in the same package, as described above [1 system of encryption].
Hopefully you will see the picture now. If not -> change the CAID/ID manually.
To do that press Exit on your Remote until you see CAID options, then press the arrows up or down to change CAID and each time you do it press OK button on your remote, too. Wait to see the picture. You will also see the new info in your GBox window on your PC. As in "CW received from..."
See bellow for Gold Emu Menu options.
===========A few more notes:========
GBox 2.1b as such [the one MAHDI adapted to Sammy] has a silly bug, so frequently isn't working and only resetting everything, including rebooting your PC AND Sammy
Sammy on its own is also a bit silly sometimes, as the Gold Emu easily looses EPG etc. In those cases I restart it by killing it with the power button at the back, for some 10 seconds, after putting it to Standby.
When you start the GBox in your Firewall you will have the GBox active under programs and it must have the free access to the net. Give it the permission it needs.
In your Router you must do the Port Forwarding. In my modem it's under Applications and Gaming -> Port Range Forwarding.
You name an application [say GBox for your GBox CS SW or maybe name it after your friend, as you may open many ports for GBox and each should be named after your friend].
Put the Port Range as follows:
-your port [the one you have to give to your friend to put into his cwsahre.cfg, together with your DynDNS and Pass] and the same port should be in Start and EndUDP or Both Protocols, and add your IP address, plus tick it at the end, so it is active. {At least that is how it is in my Linksys Router.}
-his port - the one he gave you, where you will be let into his machine, just do the same as above but name it after your friend, so you know which one is which.
-check your address by clicking on the Network Icon in the Systray -> Support
Now go to the bottom of the page and SAVE SETTINGS! If you did it the right way it should all be saved and you will see it the way you want it to be right in front of you.
If you've done it all properly, if you have the correct details of a Server, your GBox will say Hello to... then he will respond with Hello from... Change the channel and wait for the picture. Sometimes you need to choose the CAID manually and press OK for each CAID.
Also, in the Sammy Emu Menu I have:
Emu to ON,
EMM to ON,
CAID to MANUAL,
Sharing Mode to SSSP,
Channel CA Info to NOT SHOW.
Cheers and good luck!!
[I need a drink after all this... After that I need a holiday... FFS... :drinks: :Heureux05:]
====================================
Here are the instructions for earlier versions of CS SW [GBox]:
with RG EMU 5.7 we have the GBox once again - but now as an external application completely, since our beloved Sammy's memory is very limited...
Ergo, we must install it to our PC and start it from there as follows:
1) Download RG EMU by Maestro MAHDI v. 5.7 [SamsungDSR9500_RVGOLD_v5.7] and GBox Sharing SW [DSR9500GboxSharingv1.1]. Put them in the same folder.
2) Unpack RV GOLD. Rename README into RV Readme or something like that.
3) Delete GBox Folder. Click once on it and then press SHIFT + DELETE on your keyboard, then press ENTER.
4) Unpack GBox Sharing into the same folder. Just right click on the file and then EXTRACT HERE with WinRar or WinZip program.
{Program your beloved Samsung with the new RG EMU 5.7 if you haven't done so as yet, of course. The HOW TO is in this section.}
5) Put your properly sorted cwshare.cfg file into GBox folder.
{Put your Samsung on an encrypted channel you know will be opened by the server you are sharing with, of course..}
6) Start the CS program by double clicking on it: DSR9500GboxCS.
7) Now choose the COM port to which you connected your Sammy, plus choose the Debug option, too.
8) Click on CONNECT.
9) Go to GBox folder and there double click on the gbox program itself.
10) Change the channel.
Wait for it to open...
If everything is as it should be in your cwshare.cfg and if you forwarded the ports etc., as we already explained it all here in detail - it should work!
You'll see "Hello to..." and then "Hello from...", the changes of CAID etc. etc. on your monitor...
---------------------------------------------------------
I have finally played with the CS stuff again: tested with Emu RG 6.5 + CS 1.3 for Sammy and it all works quite well, except **N*D,S where the pixilation always was a problem.
Read this thread carefully - as all is explained in details - and you'll get there... :wink:
- make yourselves a DynDNS account and configure your router/modem to update it automatically
- edit your cwshare.cfg
- do the port forwarding
- configure your firewall
Step on it.... :Heureux05:
Thanx to Shadow & Ruspi for server details, so I could fool around again...
It's very easy, gals and guys! :good:
Start, after you've done the stuff I just mentioned, as described in detail, in this very thread earlier, your DSR9500GBox CSv1.3 & choose a port + tick the Debug, as before, then Connect - GBox application will be started automatically in a small black window. Change the channel. If the server you're connecting to has the card that opens the channel - you'll see pretty colours, provided you did it all right, with patience and attention to detail! Experiment a bit with the 2 Delays, to see what work best in your setup! Amen! :smile:
Every time you change something in your settings - restart your Sammy & GBox, and if necessary your PC, too.
Good luck!:wink:
P.S. Thanx to Kalkov for his opinion on this matter:
The best combination for now is emu 7.5 and gbox 1.3.
====================================
Plus, re. the latest CS Studio program v. 1.2, its plugins and CCcam in particular, which I will attach to this message:
Additionally, thanx to Maumixio, re. the latest CS Studio program, its plugins and CCcam in particular:
How to make your Samsung DSR working with CS Studio 1.1 in few steps:
Put you decoder to Sharing mode -> DSR_SSSP
copy plugin/s [you'll find attached with this post] into your local folder Plugin where the main program is located
start program and set the connection serial port (usually COM1)
set only one plugin active (see picture attached)
That's all.
How to make your working cccam: see examples .
Hadu : Server=CCCam:MyServer.com:12000:0:MyUsername:MyPas sword
Acamd: cccamn:192.168.7.54:12000:0/0000/0000:usernameassword
Flycccam (flydahli) C: xxx.xxx.xxx 12000 name pass
WinCSC edit wincsc.cfg attached (working) or edit servers in main plugin window
[Only Registered Users Can See Links]
Also :
Only one plugin at same time and you decide which one. Circles evidence in pic disabled plugins, only flydahli is enable and working just to explain procedure. All are good, my preferred is Hadu and for free, for ever free no patched or cracked absolutely free, but you need a valid cccam like the others. Wincsc works with NewCamd and it needs valid servers, sometimes available for free in the net. CS is not allowed and supported in details in SatUniverse.Additionally, from me:biggrin:
Sammy can hook onto/do the Card Sharing thing with three different protocols:
GBox server
Newcamd server
CCcam server.
So, for each one of those you will need a different way to connect to them, as I explained partially above, in this very thread, if you can be bothered to read a bit... Read slowly and carefully, plus do it, as you're reading it and all will be clear....
GBox is explained above in detail. Exactly what is needed, in every respect!
Newcamd needs an N line, quite similarly, in some ways, but simpler.
And a valid CCcam C line, i.e. somebody to give you access to their CCcam server, if that is what you choose to do... This one is the simplest, as you do not need to open any ports in your modem/router etc.
Now, read, people, educate yourselves and enjoy learning and getting independent...:good:
Card Sharing is:
connecting your receiver [in this case Samsung DSR 9500 VIACI] with a specific SW in your receiver [in this case Gold Emu 4.x by Maestro MAHDI, plus GBox (installed on your PC!) by Maestro TaGana and the possy]
with your friends' receivers or PCs.
They will have Original Smart Cards [OSCs] you do NOT have, in order to watch the programs those OSCs open.
You connect with them via the internet.
With CS you have those cards virtually. But you can still watch the programs those OSCs can open, provided your friends are constantly "online" and you can connect to their receiver or PC.
Your Sammy, btw, is connected to the net via your PC. It is done via a Serial port at the back of your Sammy to the Serial Port on your PC. A "straight" 9 pin Serial Cable is used. Meaning: the wires are connected 2->2, 3->3, 9->9 etc. I am not sure if ALL the 9 pins are connected. Check it out on the net.
And now the "How to" in small steps:
First, How to make and use a dyndns free service/account...
It's a simple but more detailed guide than the one already provided here:
go to _[Only Registered Users Can See Links] and then...
choose a username
then a password
confirm it
provide them with a valid email [you must!]
confirm it
security image - carefully put it in the box provided
click on "I agree with Terms & conditions"
click on "Create account".
You get an email.
Click on the link provided to activate the account.
Login at the dyndns.org website.
Go to: My Service -> Add hostaname -> create it: xyz.dyndns.org or something else you choose there [they have a few].
Click on “Use auto detected IP address xx.xxx.xxx.xx”.
"Add To Cart" -> it will say something like “You must checkout to activate”.
Click on "Next" and then on
"Activate Service".
You should see: “Host Services successfully activated”.
Go and CS... :wink:
Login regularly [weekly] so they don’t delete your account! They do it without any warning!
Btw, GBox, [and the SSSP derivatives, like MGcamd and Mbox, for instance], needs this to function, for both Client and Server services. If you only use CCcam client service, it is not needed. The following will be in relation to GBox...:wink:
After that put the DynDNS details into your Router to enable your DynDNS Service updater in it, so DynDNS Service is updated every time you change your IP address and your friends can find you through the DynDNS address. Namely, in your router's DDNS options [if you have more than one]:
choose DynDNS, then ->
put your newly created DynDNS username, then
password, then
Hostname [like myname.dyndns.org - this is just an example, create your own name!!].
That address you just created is always going to be the same, even though your IP address might change every time you logon/get online/boot your PC.
Now SAVE all that or APPLY or ENABLE, whatever is in your Router's interface.
OK so far? :blush:
After that you need to forward some ports in your Router. That allows your GBox to go to the net and connect with other PCs, in this case a Server with your friends' cards, the stuff you want to watch...
Now, install UltraEdit32 on your PC. Why? Because you need to sort your cwshare.cfg yourself. Here is the template you need to Copy and Paste into UltraEdit 32, NOT Notepad, Wordpad or anything else!!!
In cwshare.cfg you will edit the yourdyndns.org and yourfriendsdyndns.whatever with the data you are given from the people you trust, like theirport but also yourport, the one you assign to your GBox, so it can go to the net. Also yourpass and hispass! JUST REPLACE THEM AS INDICATED BELLOW, IT IS EASY!!! Don't give up on me now!!! :bangin:
That's all you need to do for Sammy GBox to work your CS magic. Nothing else. No other files except cwshare.cfg!!!
===============cwshare.cfg=============
Lines with # in front are not taken into account, do not matter, these are explanations. Leave them be.
M: { your.dyndns.org { yourpass }}
# Internet Friends port range password cod
D: { yourfriendsdyndns.whatever { yourport theirport { hispass { A3 A3 }}}}
#================================================
# allow maximum 3 share level for received card data
I: { 3 }
# Send ECM's at maximum 7 cards (please use this as default)
X: { 7 }
#
# 01 repeat EMM's
# 00 consider every EMM only once
# 01 restart pid on overflow
# 1* reset ENX on every channel change
# *1 check/reset ENX freezes on FTA
# *2 check/reset ENX freezes on PayTV
# *3 check/reset ENX freezes on FTA and PayTV
# 00 write nothing in atack.txt
# 01 write into atack.txt: password is wrong
# 02 write into atack.txt: ID unknown
# 04 write into atack.txt: IP is wrong
# 08 write into atack.txt: port is wrong
# 10 write into atack.txt: share.stat
# 20 create online.log for online/offline logging
# 3F write everything. (combine bits for other combinations)
# 5000 send ecm again after 5 Seconds if no reply.
# 7000 resync decode after 7 Seconds if net decode failed
N: { 01 01 03 00 5000 7000 }Lines with # in front are not taken into account, do not matter, these are explanations. Leave them be.
Your pass will be 8 signs, letters from A - F, if memory serves, numbers from 1-9.
Just Copy and Paste this into your Ultra Edit 32 and edit CAREFULLY, preserving the empty slots [pauses/breaks], then Save.
==============To recapitulate:=================
You have created a DynDNS account and enabled it in your router.
You have installed UE32 and created a GBox folder [just unpack your GBox in that folder] on your PC.
In your cwshare.cfg file, that is a part of GBox CS SW, you have put your DynDNS details and the password for your GBox, plus the ports you have opened in your Router for it to operate freely.
You have also put your friend's details [their DynDNS address, password and port they opened for you to hook onto their GBox server] into the cwshare.cfg.
Now reboot your PC, just in case, put your Sammy on Standby, then restart it at the back with the power switch, just in case. I.e. kill the power at the back, wait for 10 seconds, turn it back on again, wait for the clock to appear on Sammy's display.
When all is ON again, as described above, start your Sammy with your Remote and put it on a scrambled channel [with just 1 system of encryption, preferably not N*D*S/Videguard, as it's difficult].
Start your GBox with the newly edited cwshare.cfg, that you put into the GBox folder.
You should see a new black window on your PC, with something like "Hello to..."
Then "Hello from..." [your friend] should appear. That is IF you are connected, if everything is properly sorted.
Change the channel to another encrypted channel in the same package, as described above [1 system of encryption].
Hopefully you will see the picture now. If not -> change the CAID/ID manually.
To do that press Exit on your Remote until you see CAID options, then press the arrows up or down to change CAID and each time you do it press OK button on your remote, too. Wait to see the picture. You will also see the new info in your GBox window on your PC. As in "CW received from..."
See bellow for Gold Emu Menu options.
===========A few more notes:========
GBox 2.1b as such [the one MAHDI adapted to Sammy] has a silly bug, so frequently isn't working and only resetting everything, including rebooting your PC AND Sammy
Sammy on its own is also a bit silly sometimes, as the Gold Emu easily looses EPG etc. In those cases I restart it by killing it with the power button at the back, for some 10 seconds, after putting it to Standby.
When you start the GBox in your Firewall you will have the GBox active under programs and it must have the free access to the net. Give it the permission it needs.
In your Router you must do the Port Forwarding. In my modem it's under Applications and Gaming -> Port Range Forwarding.
You name an application [say GBox for your GBox CS SW or maybe name it after your friend, as you may open many ports for GBox and each should be named after your friend].
Put the Port Range as follows:
-your port [the one you have to give to your friend to put into his cwsahre.cfg, together with your DynDNS and Pass] and the same port should be in Start and EndUDP or Both Protocols, and add your IP address, plus tick it at the end, so it is active. {At least that is how it is in my Linksys Router.}
-his port - the one he gave you, where you will be let into his machine, just do the same as above but name it after your friend, so you know which one is which.
-check your address by clicking on the Network Icon in the Systray -> Support
Now go to the bottom of the page and SAVE SETTINGS! If you did it the right way it should all be saved and you will see it the way you want it to be right in front of you.
If you've done it all properly, if you have the correct details of a Server, your GBox will say Hello to... then he will respond with Hello from... Change the channel and wait for the picture. Sometimes you need to choose the CAID manually and press OK for each CAID.
Also, in the Sammy Emu Menu I have:
Emu to ON,
EMM to ON,
CAID to MANUAL,
Sharing Mode to SSSP,
Channel CA Info to NOT SHOW.
Cheers and good luck!!
[I need a drink after all this... After that I need a holiday... FFS... :drinks: :Heureux05:]
====================================
Here are the instructions for earlier versions of CS SW [GBox]:
with RG EMU 5.7 we have the GBox once again - but now as an external application completely, since our beloved Sammy's memory is very limited...
Ergo, we must install it to our PC and start it from there as follows:
1) Download RG EMU by Maestro MAHDI v. 5.7 [SamsungDSR9500_RVGOLD_v5.7] and GBox Sharing SW [DSR9500GboxSharingv1.1]. Put them in the same folder.
2) Unpack RV GOLD. Rename README into RV Readme or something like that.
3) Delete GBox Folder. Click once on it and then press SHIFT + DELETE on your keyboard, then press ENTER.
4) Unpack GBox Sharing into the same folder. Just right click on the file and then EXTRACT HERE with WinRar or WinZip program.
{Program your beloved Samsung with the new RG EMU 5.7 if you haven't done so as yet, of course. The HOW TO is in this section.}
5) Put your properly sorted cwshare.cfg file into GBox folder.
{Put your Samsung on an encrypted channel you know will be opened by the server you are sharing with, of course..}
6) Start the CS program by double clicking on it: DSR9500GboxCS.
7) Now choose the COM port to which you connected your Sammy, plus choose the Debug option, too.
8) Click on CONNECT.
9) Go to GBox folder and there double click on the gbox program itself.
10) Change the channel.
Wait for it to open...
If everything is as it should be in your cwshare.cfg and if you forwarded the ports etc., as we already explained it all here in detail - it should work!
You'll see "Hello to..." and then "Hello from...", the changes of CAID etc. etc. on your monitor...
---------------------------------------------------------
I have finally played with the CS stuff again: tested with Emu RG 6.5 + CS 1.3 for Sammy and it all works quite well, except **N*D,S where the pixilation always was a problem.
Read this thread carefully - as all is explained in details - and you'll get there... :wink:
- make yourselves a DynDNS account and configure your router/modem to update it automatically
- edit your cwshare.cfg
- do the port forwarding
- configure your firewall
Step on it.... :Heureux05:
Thanx to Shadow & Ruspi for server details, so I could fool around again...
It's very easy, gals and guys! :good:
Start, after you've done the stuff I just mentioned, as described in detail, in this very thread earlier, your DSR9500GBox CSv1.3 & choose a port + tick the Debug, as before, then Connect - GBox application will be started automatically in a small black window. Change the channel. If the server you're connecting to has the card that opens the channel - you'll see pretty colours, provided you did it all right, with patience and attention to detail! Experiment a bit with the 2 Delays, to see what work best in your setup! Amen! :smile:
Every time you change something in your settings - restart your Sammy & GBox, and if necessary your PC, too.
Good luck!:wink:
P.S. Thanx to Kalkov for his opinion on this matter:
The best combination for now is emu 7.5 and gbox 1.3.
====================================
Plus, re. the latest CS Studio program v. 1.2, its plugins and CCcam in particular, which I will attach to this message:
Additionally, thanx to Maumixio, re. the latest CS Studio program, its plugins and CCcam in particular:
How to make your Samsung DSR working with CS Studio 1.1 in few steps:
Put you decoder to Sharing mode -> DSR_SSSP
copy plugin/s [you'll find attached with this post] into your local folder Plugin where the main program is located
start program and set the connection serial port (usually COM1)
set only one plugin active (see picture attached)
That's all.
How to make your working cccam: see examples .
Hadu : Server=CCCam:MyServer.com:12000:0:MyUsername:MyPas sword
Acamd: cccamn:192.168.7.54:12000:0/0000/0000:usernameassword
Flycccam (flydahli) C: xxx.xxx.xxx 12000 name pass
WinCSC edit wincsc.cfg attached (working) or edit servers in main plugin window
[Only Registered Users Can See Links]
Also :
Only one plugin at same time and you decide which one. Circles evidence in pic disabled plugins, only flydahli is enable and working just to explain procedure. All are good, my preferred is Hadu and for free, for ever free no patched or cracked absolutely free, but you need a valid cccam like the others. Wincsc works with NewCamd and it needs valid servers, sometimes available for free in the net. CS is not allowed and supported in details in SatUniverse.Additionally, from me:biggrin:
Sammy can hook onto/do the Card Sharing thing with three different protocols:
GBox server
Newcamd server
CCcam server.
So, for each one of those you will need a different way to connect to them, as I explained partially above, in this very thread, if you can be bothered to read a bit... Read slowly and carefully, plus do it, as you're reading it and all will be clear....
GBox is explained above in detail. Exactly what is needed, in every respect!
Newcamd needs an N line, quite similarly, in some ways, but simpler.
And a valid CCcam C line, i.e. somebody to give you access to their CCcam server, if that is what you choose to do... This one is the simplest, as you do not need to open any ports in your modem/router etc.
Now, read, people, educate yourselves and enjoy learning and getting independent...:good: